工厂重置头像2.0#

(NitroPad - Ubuntu Linux)

重置为出厂设置的原因#

  • 您的Nitrokey被锁定(例如,由于多次输入错误的PIN码)。

  • 你丢失了你的Nitrokey(在这种情况下,你首先需要一个新的)。

  • 你自己安装了一个操作系统(例如在更换硬盘后)。

  • 你的操作系统不能启动

警告

如果你重置你的设备,Nitrokey上的所有数据都将丢失。因此,在执行重置之前,请备份你的数据。

程序#

  1. 将你的Nitrokey连接到NitroPad。

  2. 开启NitroPad。

  3. 选择 “选项”。

头部选项菜单
  1. 选择 “OEM-Factory Reset /Re-Ownership”。

重置
  1. 用 “继续 “确认重置。

确认
  1. 您的设置的完整性将被测试,取决于您执行重置的原因,这可能会失败,但无论如何都会继续。

确认完整性
  1. 下面的问题都可以用 “默认 “来回答。如果你只想重置你的设备,就按回车键。

Would you like to change the current LUKS Disk Recovery Key passphrase?
 (Highly recommended if you didn't install the Operating System yourself, so that past provisioned passphrase would not permit to access content.
 Note that without re-encrypting disk, a backuped header could be restored to access encrypted content with old passphrase) [y/N]: N

Would you like to re-encrypt LUKS encrypted container and generate new Disk Recovery key?
 (Highly recommended if you didn't install the operating system yourself: this would prevent any LUKS backuped header to be restored to access encrypted data) [y/N]: N

The following security components will be provisioned with defaults or chosen PINs/passwords:

TPM Ownership password
GPG Admin PIN
GPG User PIN

Would you like to set a single custom password that will be provisioned to previously stated security components? [y/N]: N

Would you like to set distinct PINs/passwords to be provisioned to previously stated security components? [y/N]: N

Would you like to set custom user Information for the GnPG key?[y/N]: N

Would you like to set custom user information for the GnuPG key? [y/N]: N

Checking for USB Security Dongle...

Detecting and setting boot device...

Boot device set to /dev/nvme0n1p2

Resetting TPM...

Resetting GPG Key...
(this will take around 3 minuts...)

Changing default GPG Admin PIN

Changing default GPG User PIN

Reading current firmware
(this will take a minute or two)

Adding generated key to current firmware and re-flashing...

Signing boot files and generating checksums
  1. 它将显示默认的GPG PINS和TPM密码

违约
  1. 确认随后的重新启动。

重新启动
  1. 重新启动后,必须创建OTP秘密。用回车键确认该过程。

OTP秘密生成确认1
OTP秘密生成确认2
  1. 输入TPM密码(默认:12345678)。

tpm密码输入
  1. 用手机扫描二维码,输入TOTP Seceret(可选)并点击回车。

QR代码TOTP
  1. 当出现提示时,输入你的Nitrokey的管理密码(默认:12345678)并点击回车键。

管理引脚硝基键输入
  1. 然后你应该到达 “开始 “菜单。

开始菜单
  1. 按回车键,开始 “默认启动”。

注解

如果你看到还没有默认值的信息,请按照 “故障排除 “中描述的程序操作。默认启动菜单”。