Nitrokey FIDO2 With Windows#

The Nitrokey FIDO2 supports two-factor authentication (2FA) and passwordless authentication:

  • With passwordless authentication, entering a password is replaced by logging in with the Nitrokey FIDO2 and a PIN.

  • With two-factor authentication (2FA), the Nitrokey FIDO2 is checked in addition to the password.

The Nitrokey FIDO2 can be used with any current browser.

Important

The Nitrokey App can not be used for the Nitrokey FIDO2.

Tip

Check online if your Nitrokey FIDO2 has the latest firmware installed.

Passwordless Authentication#

  1. Open a web page that supports FIDO2 (for example Google).

  2. Log in to the website and go to “Passkeys and security keys” in the security settings of your account.

  3. Click on Create passkey.

  4. Click on Use a different device.

  5. Follow the prompts to set a PIN for your Nitrokey FIDO2.

  6. Touch the button of your Nitrokey FIDO2 when prompted.

  7. Once you have successfully configured the device, you will need to activate your Nitrokey FIDO2 this way each time you log in, after entering your PIN.

Two-Factor Authentication (2FA)#

  1. Open one of the websites that support FIDO U2F.

  2. Log in to the website and enable two-factor authentication in your account settings. (In most cases you will find a link to the documentation of the supported web service at dongleauth.com)

  3. Register your Nitrokey FIDO2 in the account settings by touching the button to activate the Nitrokey FIDO2. After you have successfully configured the device, you must activate the Nitrokey FIDO2 this way each time you log in.

You are now ready to go.

Touch Button And LED Behavior#

The first FIDO operation is automatically accepted within two seconds after connecting Nitrokey FIDO2. In this case touching the touch button is not required.

Multiple operations can be accepted by a single touch. For this, keep the touch button touched for up to 10 seconds.

To avoid accidental and malicious reset of the Nitrokey, the required touch confirmation time for the FIDO2 reset operation is longer and with a distinct LED behavior (red LED light) than normal operations. To reset the Nitrokey FIDO2, confirm by touching the touch button for at least 5 seconds until the green or blue LED lights up.

LED Color

Event

Time Period

Comments

Any (blinking)

Awaiting for touch

Until touch is confirmed or timed out

Any (blinking faster)

Touch detected, counting seconds

Until touch is confirmed or timed out

White (blinks)

Touch request for FIDO registration or authentication operation

Requires 1 second touch to complete; timeout is usually about 30 seconds

Yellow (blinks)

Touch request for configuration operation

Requires 5 seconds touch to complete; e.g. used for activating firmware update mode

Red (blinks)

Touch request for reset operation

Available only during the very first 10 seconds after Nitrokey is powered

Requires 5 seconds touch to complete; e.g. used for FIDO2 reset operation

Green (constant)

Touch accepted, Nitrokey is active and accepting further FIDO2 operations

After touch was registered, 10 seconds timeout

For the FIDO registration or authentication operations after a confirmation Nitrokey enters into “activation” mode, auto-accepting any following mentioned operations until touch button is released, but not longer than 10 seconds

Blue (constant)

Touch consumed - accepted and used up by the operation

Until touch is released

Touch consumption here means, that without releasing the touch button, and touching again the Nitrokey will not confirm any new operations

White (single blink)

Nitrokey ready to work

0.5 seconds after powering up

(no LED signal)

Nitrokey is idle

(no LED signal)

Auto-accept single FIDO registration or authentication operation

Within first 2 seconds after powering up

Nitrokey is automatically accepting any single FIDO registration or authentication operation upon insertion event - the latter is treated as an equivalent of the touch button registration signal (user presence); the conf iguration/reset operations are not accepted

All colors

Nitrokey is in Firmware Update mode

Active until firmware update operation is successful, or until reinsertion

If the firmware update fails, the Nitrokey will stay in the this mode until the firmware is written correctly

Note: white LED blinking is used as well to signalize the selected device (the so called WINK command).