Elliptic Curves (ECC) Support¶
(Nitrokey Storage 2 - Windows)
For security reasons, the German Federal Office for Information Security (Bundesamt für Sicherheit in der Informationstechnik, BSI) no longer recommends RSA keys with a length of 2048 bit to be used after 2022. This means that longer keys will need to come into use in the foreseeable future. Assuming a usage period of five years, is is already necessary to generate longer keys. However, longer RSA keys with 3072 bit or 4096 bit are significantly slower. For this reason the new Nitrokey Storage 2 and Pro 2 (resp. the integrated OpenPGP Card version 3.3) supports encryption by means of elliptic-curve cryptography (ECC). This method is considered to be just as secure with smaller ECC keys as longer RSA keys and is also considerably faster.
In contrast to RSA, there are many different forms (so-called curves) of elliptic-curve cryptography. Notably, the NSA was involved in the development of the NIST curves. Even if there is no evidence of back doors in the curves, using a certain curve can pose a question of trust. Fortunately the new Nitrokey Storage 2 and Pro 2 support two kind of curves, namely NIST and Brainpool. In what follows we will use Brainpool curves. This article provides a good entry point for gaining a general understanding of elliptic-curve cryptography.
In order to create keys based on elliptic curves a Nitrokey Storage 2 / Pro 2 and GnuPG version 2.1.17 or higher are required.
You can read Nitrokey’s OpenPGP Card version via
> gpg2 --card-status Reader ...........: 20A0:... Application ID ...: D276... Version ..........: 3.3 ...
The ‘Version’ field represents the version of the OpenPGP Card integrated in the Nitrokey — in this case it is 3.3 as needed for Elliptic-curve cryptography. OpenPGP Card version 2.2 doesn’t support ECC.
You can learn about the installed version of GnuPG via
gpg2 --version. At least version 2.1.16 is required. The newest GnuPG version for Windows can be found here and the newest version for MacOS can be found here. A suitable version of GnuPG is included in the GNU/Linux distributions Ubuntu (since 18.04), Debian (from Stretch onwards), Arch Linux, Fedora (from Release 26 onwards) and openSUSE Tumbleweed. At the end of this articles are instructions how to manually update GnuPG on older Ubuntu versions.
GnuPG 2.0 is still being used, but support for it has been discontinuied in 2017. All communication partners must use GnuPG 2.1 or newer for email encryption by means of ECC, otherwise incompatibility issues might arise. Therefore you should only use ECC if you are sure you will be able to circumvent this problem.
Once these requirements are fulfilled, you can get started. (Warning: existing keys will be overwritten in the process!) You now have two options. The first option is to create the key directly on the Nitrokey Storage 2 / Pro 2. The benefit here is that the key will never be outside the device and as such can never be read out. The second option is to import a previously locally generated key. The advantage in this case is that you can securely store a backup of the key, which can then be restored in case the Nitrokey is lost. Only the first option is described below. In order to create a key with backup, you can access the following instructions and use this general information to transfer the key to the Nitrokey.
Within GnuPG there is already a “generate” command, which can be used to easily create keys on the device. However it is not as yet possible to select the type of key directly, so the key must first be prepared. We use the following commands for this:
> gpg-connect-agent "SCD SETATTR KEY-ATTR --force 1 19 brainpoolP256r1" /bye > gpg-connect-agent "SCD SETATTR KEY-ATTR --force 2 18 brainpoolP256r1" /bye > gpg-connect-agent "SCD SETATTR KEY-ATTR --force 3 19 brainpoolP256r1" /bye
Alternatively, other curves could be selected, as described in the next section.
Now we enter
gpg2 --card-edit and see that brainpoolP256r1 is under
“key attributes” instead of rsa2048.
> gpg2 --card-edit Reader ...........: 20A0:4109:0000000000000:0 Application ID ...: D276000124010303000500005F100000 Version ..........: 3.3 Manufacturer .....: ZeitControl Serial number ....: 00005F10 Name of cardholder: [not set] Language prefs ...: [not set] Sex ..............: unspecified URL of public key : [not set] Login data .......: [not set] Signature PIN ....: forced Key attributes ...: brainpoolP256r1 brainpoolP256r1 brainpoolP256r1 Max. PIN lengths .: 64 64 64 PIN retry counter : 3 0 3 Signature counter : 0 Signature key ....: [none] Encryption key....: [none] Authentication key: [none] General key info..: [none]
Then we create the key.
gpg/card> admin Admin commands are allowed gpg/card> generate Make off-card backup of encryption key? (Y/n) n Please note that the factory settings of the PINs are PIN = '123456' Admin PIN = '12345678' You should change them using the command --change-pin Please specify how long the key should be valid. 0 = key does not expire <n> = key expires in n days <n>w = key expires in n weeks <n>m = key expires in n months <n>y = key expires in n years Key is valid for? (0) Key does not expire at all Is this correct? (y/N) y GnuPG needs to construct a user ID to identify your key. Real name: Jane Doe Email address: email@example.com Comment: You selected this USER-ID: "Jane Doe <firstname.lastname@example.org>" Change (N)ame, (C)omment, (E)mail or (O)kay/(Q)uit? O gpg: key 7F8C68E1B084E169 marked as ultimately trusted gpg: revocation certificate stored as '/home/jane/.gnupg/openpgp-revocs.d/F8C00BC1636A7D7604A31A877F8C68E1B084E169.rev' public and secret key created and signed.
The Nitrokey now incorporates elliptic-curve cryptography instead of RSA keys and can be used as usual.
In the above procedure we chose the Brainpool curves. Alternatively, NIST curves can be used. The configuration is carried out as follows:
> gpg-connect-agent "SCD SETATTR KEY-ATTR --force 1 19 nistp256" /bye > gpg-connect-agent "SCD SETATTR KEY-ATTR --force 2 18 nistp256" /bye > gpg-connect-agent "SCD SETATTR KEY-ATTR --force 3 19 nistp256" /bye
The following steps are needed only if you are running a Ubuntu version older than 18.04. You can install GnuPG 2.1.18 on such system with the commands below. This involves newer Debian packages, which is the easiest option. This approach has been tested successfully on Ubuntu 17.10 and propbably works on 16.04 as well. However, the occurence of problems during usage can‘t be excluded.
$ mkdir gnupg_tmp $ cd gnupg_tmp $ wget http://ftp.debian.org/debian/pool/main/g/gnupg2/gnupg_2.1.18-8~deb9u1_amd64.deb $ wget http://ftp.debian.org/debian/pool/main/g/gnupg2/dirmngr_2.1.18-8~deb9u1_amd64.deb $ wget http://ftp.debian.org/debian/pool/main/g/gnupg2/gnupg-agent_2.1.18-8~deb9u1_amd64.deb $ wget http://ftp.debian.org/debian/pool/main/g/gnupg2/scdaemon_2.1.18-8~deb9u1_amd64.deb $ sudo dpkg -i * $ cd .. $ rm -rf gnupg_tmp
In case you want to undo the installation, you have to execute the following commands:
$ sudo dpkg --remove --force-depends gnupg dirmngr gnupg-agent scdaemon # (removes manually installed packages) $ sudo apt-get install gnupg dirmngr gnupg-agent scdaemon # (installs the appropriate packages from regular package repositories)