Ubuntu¶
Проверка на запечатан хардуер¶
If you have ordered the unit with the option “sealed screws and sealed bag”, please verify the sealing before unpacking. If you do not know what this means, skip this section.
Процедура за сигурно стартиране¶
With the NitroPad and NitroPC, malicious changes to the BIOS, operating system, and software can be easily detected. For example, if you left your NitroPad in a hotel room, you can use your Nitrokey to check if it has been tampered with while you were away. If an attacker modifies the NitroPad’s firmware or operating system, the Nitrokey will detect this (instructions below).
Each time you start the NitroPad or the NitroPC, you should - if possible - connect your Nitrokey. If the Nitrokey is plugged in and the system has not been modified, the following screen will appear when it is turned on.

The box marked in red contains the information that the BIOS has not been changed and that the shared secret of the NitroPad or the NitroPC and the Nitrokey match. But this information is not sufficient, because an attacker could have faked it. If at the same time the Nitrokey also flashes green, everything is fine. An attacker would have to have had access to the NitroPad or NitroPC and Nitrokey to achieve this result. It is therefore important that you do not leave both devices unattended.
If the information on the NitroPad or NitroPC does not match the information on the Nitrokey, the background would turn red and the message “Invalid Code” would appear. This could indicate that manipulation has taken place.

По-долу е описано как може да изглежда процесът на зареждане, ако системата е била променена (например след актуализация), и какви съобщения за грешки могат да се появят в противен случай.
Tip
The NitroPad and NitroPC can also be started without the Nitrokey. If you don’t have the Nitrokey with you, but are sure that the hardware has not been manipulated, you can boot your system without checking.
Обходен път Ubuntu 24.04.¶
Съществува (issue)която пречи на Ubuntu да покаже екрана за декриптиране на luks, ако е стартиран с heads. Той е там и можете да въведете паролата си на сляпо, след което Ubuntu започва нормално. Следвайте тези стъпки:
Началото е в главата. Ако не е необходимо да се прави нищо, Ubuntu ще се стартира автоматично
След известно време ще видите черен екран с бял надпис на последните редове:
Locking TPM2 platform hierarchy...
Starting the new kernel
Тези редове показват, че Ubuntu се стартира.
Изчакайте 5 секунди и след това въведете своята парола („12345678“, ако го стартирате за първи път), последвана от Въведете.
Сега ще видите нормалния екран на Ubuntu. Когато стартирате за първи път, трябва да завършите първоначалната конфигурация.
Започване на работа¶
След покупката паролите са зададени по подразбиране и трябва да бъдат променени от вас:
Натиснете Enter („Default Boot“) след стартиране на системата, при условие че NitroPad не е показал никакви грешки и Nitrokey свети в зелено (вж. по-горе).
След това системата ще ви подкани да въведете паролата, за да декриптирате твърдия диск. Първоначално паролата е „12345678“. Тя беше променена на 10.04.2024 г., така че ако „12345678“ не работи, опитайте старата по подразбиране: „PleaseChangeMe“.
След това системата ще ви насочи към процеса на създаване на потребителски акаунт. След това трябва да сте стартирали успешно системата и вече да можете да я използвате нормално.
Open the pre-installed Nitrokey App and change the PINs of your Nitrokey. To learn more about how to change the PINs, please refer to chapter Change User and Admin PIN.
Променете паролата за криптиране на диска. За да научите повече за това как да промените паролата за криптиране на диска, моля, вижте глава Промяна на паролата за криптиране на диска. Тази парола се различава от паролата на потребителския ви акаунт‘.
Поведение след актуализация на системата¶
The NitroPad and NitroPC firmware checks certain system files for changes. If your operating system has updated important components, you will be warned the next time you boot the NitroPad or NitroPC. This could look like this, for example:

That’s why it’s important to restart your NitroPad or your NitroPC under controlled conditions after a system update. Only when the new status has been confirmed can you leave the device unattended again. Otherwise, you will not be able to distinguish a possible attack from a system update. Detailed instructions for a system update can be found here.